93-02 V6 Tech V6 Camaro General Topics.

3K rpm at idle, tries to die if you touch the gas

Old Oct 4, 2011 | 04:25 PM
  #1  
texas_RS's Avatar
Thread Starter
|
In the Staging Lanes
Joined: Nov 2010
Posts: 73
From: Palestine Tx.
Default 3K rpm at idle, tries to die if you touch the gas

ok so i just baught a 97 3.8 yesterday for $400 and when i got it home i tried to crank it. it it very hard to crank you have to prime the fuel pump like 4 times then it cranks but idles at 3K rpm... now when you give it gas it jerks and jumps and tries to die, and if you get it rolling it drive a few seconds and acts like it shuts off. it you press the clutch in just a hair it runs ok, but still chokes if given gas... cleaned the TB and the MAF, TPS are new... the guy i baught it from gave up on it so does anybody have any ideas??? ANY AND ALL HELP IS GREATLY APPRECIATED!!!
 
Old Oct 4, 2011 | 06:01 PM
  #2  
BasicConcepts's Avatar
Overdrive Member
Joined: Oct 2009
Posts: 4,597
From: Greenville, South Carolina
Technical User
Default

Iac maybe???
 
Old Oct 4, 2011 | 06:08 PM
  #3  
Gorn's Avatar
Fourth Generation Moderator
October 2009 ROTM
iTrader: (1)
Joined: Nov 2007
Posts: 10,560
From: Eastern PA,
ROTM Winner's Club
Default

Check your fuel pressure. Any codes? Have you tried disconnecting the MAF sensor? Check it for vacuum leaks. If it is idleing at 3000 RPM its getting air from someplace.
 
Old Oct 4, 2011 | 06:19 PM
  #4  
texas_RS's Avatar
Thread Starter
|
In the Staging Lanes
Joined: Nov 2010
Posts: 73
From: Palestine Tx.
Default

i am about to check the IAC... not sure about the fuel pressure, gna try the MAF right now and the only code is for a vacuum leak but i cant find one anywhere...
 
Old Oct 4, 2011 | 08:25 PM
  #5  
BasicConcepts's Avatar
Overdrive Member
Joined: Oct 2009
Posts: 4,597
From: Greenville, South Carolina
Technical User
Default

Code for a vac leak??? What's the number???
 
Old Oct 4, 2011 | 08:33 PM
  #6  
Socom's Avatar
November 2010 ROTM
October 2011 ROTM
Joined: Jan 2010
Posts: 1,104
From: Maryland
ROTM Winner's Club
Default

You said the car jerks a bit when you give it gas. Is the clutch not disengaging all the way?
 
Old Oct 5, 2011 | 05:26 PM
  #7  
texas_RS's Avatar
Thread Starter
|
In the Staging Lanes
Joined: Nov 2010
Posts: 73
From: Palestine Tx.
Default

not the whole car just the motor, it bucks hard... just for safe measure i changed the MAF, AIC, and the TPS and the only code it read last night what TPS low voltage... i fixed the vacuum leak yesterday. and the vac code was either 102 or 122 not sure but that is fixed, had a cracked hose...
 
Old Oct 5, 2011 | 07:35 PM
  #8  
texas_RS's Avatar
Thread Starter
|
In the Staging Lanes
Joined: Nov 2010
Posts: 73
From: Palestine Tx.
Default

the code is saying TPS low voltage but ive checked it and everything in the loop with it and everything has power just as it should so what could it be? everything else is scanning to be running just fine so idk...
 
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
runner66
2010+ General
5
Sep 13, 2010 12:57 PM
BigNic
Detailing
12
May 30, 2008 06:44 PM


Thread Tools
Search this Thread

All times are GMT -5. The time now is 11:58 PM.