Camaro Forums - Chevy Camaro Enthusiast Forum
DSC01492 resize[1]
DSC01492 resize[1]
0 2010/06/01 01:43:12
DSC01482 resize[1]
DSC01482 resize[1]
0 2010/06/01 01:43:12
DSC01478 resize[1]
DSC01478 resize[1]
0 2010/06/01 01:43:12
Mark 8 fan install will be making some brackets soon to hold it place
Mark 8 fan install will be making some brackets soon to hold it place
0 2010/05/29 04:02:23
Wiring and relays for the the mark 8 fan I'm installing
Wiring and relays for the the mark 8 fan I'm installing
0 2010/05/29 04:02:23
under car pic
under car pic
0 2010/04/13 19:18:21
Fuel filter install
Fuel filter install
0 2010/04/13 19:05:02
7 gauges install
7 gauges install
0 2010/04/13 19:05:02
panhardbers came in today look very good paid only $124.00 for the set
panhardbers came in today look very good paid only $124.00 for the set
0 2010/04/01 08:56:58
1/2 braided gas line run under car.
1/2 braided gas line run under car.
0 2010/03/24 21:22:03
getting it back together.
getting it back together.
0 2010/03/24 21:13:59
Up date pic of the motor
Up date pic of the motor
0 2010/03/24 21:13:59
New fuel filter and 1/2 braided lines from the gas tank to the front of the car.
New fuel filter and 1/2 braided lines from the gas tank to the front of the car.
0 2010/03/24 21:13:59
Went out to the park to clean up the car
Went out to the park to clean up the car
0 2010/03/14 07:53:03
DSC00091
DSC00091
0 2010/03/05 18:05:19
DSC00097
DSC00097
0 2010/03/05 18:05:19
Valve covers are procomp with 4 edelbrock breathers. I'm from old school my Dad race back in the late 40s 50s 60s he always said let the engine crank vent at higher rpm.
Valve covers are procomp with 4 edelbrock breathers. I'm from old school my Dad race back in the late 40s 50s 60s he always said let the engine crank vent at higher rpm.
0 2010/03/05 17:57:54
Edelbrock nascar rpm air gap intake and blue printed holley 735 cfm
Edelbrock nascar rpm air gap intake and blue printed holley 735 cfm
0 2010/03/05 17:57:54
Pic of the exhaust with magaflow
Pic of the exhaust with magaflow
0 2010/03/05 17:57:54
Motor bay wiring cut out.
Motor bay wiring cut out.
0 2010/03/05 17:44:59
Man all these wire's in the motor bay, I just cut them out and started all over again.
Man all these wire's in the motor bay, I just cut them out and started all over again.
0 2010/03/05 17:44:59
New 4 row radiator
New 4 row radiator
0 2010/03/05 11:02:33
jagpicsneads246
jagpicsneads246
0 2010/03/05 11:02:33
t motorpics081 1
t motorpics081 1
0 2010/03/05 09:12:30
t motorpics060
t motorpics060
0 2010/03/05 09:12:30
motor color is red..
motor color is red..
0 2010/03/05 09:12:30
Me and my wife getting ready to install the motor
Me and my wife getting ready to install the motor
2 2010/03/05 09:05:14
blue printed 735 cfm holley
blue printed 735 cfm holley
0 2010/03/05 09:05:14
Block and crank came back from the machine shop building the motor.
Block and crank came back from the machine shop building the motor.
1 2010/03/05 09:05:14
Heads are procomp 57cc chambers 210 runner's 2.02/1.60 valves. only did a little port work on the exhaust side.
Heads are procomp 57cc chambers 210 runner's 2.02/1.60 valves. only did a little port work on the exhaust side.
0 2010/03/05 08:48:40
Man what a job wiring, going through all the wiring, and cut out one's I'm not using.
Man what a job wiring, going through all the wiring, and cut out one's I'm not using.
0 2010/03/05 08:48:40
crank tapping
crank tapping
0 2010/03/05 08:35:33
The color inside the was red and change it to the color you see now.
The color inside the was red and change it to the color you see now.
0 2010/03/05 05:44:47
New radiator 4 row dual fans 1 fan comes at 185 and the 2nd kicks on at 195
New radiator 4 row dual fans 1 fan comes at 185 and the 2nd kicks on at 195
0 2010/03/05 05:44:47
motor rev up to 7000 rpm by time I took the picture it drop down to 6400 rpm
motor rev up to 7000 rpm by time I took the picture it drop down to 6400 rpm
0 2010/03/05 05:25:42
crank tap bolt fits
crank tap bolt fits
0 2010/03/03 10:11:36
Had to tap the crank the machine shop for got to do it when they balance it for me.
Had to tap the crank the machine shop for got to do it when they balance it for me.
0 2010/03/03 09:28:49
Inside pic lift side
Inside pic lift side
0 2010/03/03 08:46:23
Inside pics right side
Inside pics right side
0 2010/03/03 08:46:23
0 2010/01/28 10:23:16