Detailing Discuss detailing your ride within.

Undercoating removal

Thread Tools
 
Search this Thread
 
  #1  
Old 08-15-2009 | 09:42 PM
gray80's Avatar
Thread Starter
|
Newbie
Joined: Jul 2009
Posts: 29
From: North Central Illinois
Default Undercoating removal

I have a very nice 1980 Z that was undercaoted at the dealer 30 years ago. I am trying to find the right chemical to use on areas where the undercoating is on finshed areas of the car. The objective here is to remove only the coating and leaving the finish intact.
Can any of my Camaro Enthusiats bretheren lead me to the right chemical to use on my Z?
Thanks
Gray 80
 
  #2  
Old 08-16-2009 | 06:33 PM
GMDCAMARO's Avatar
3rd Gear Member
Joined: Oct 2007
Posts: 1,289
From: Utah
Default

We use acetone on a microfiber towel here at the shop.

Were exactly is it? Is it thick?
 
  #3  
Old 08-18-2009 | 10:34 PM
gray80's Avatar
Thread Starter
|
Newbie
Joined: Jul 2009
Posts: 29
From: North Central Illinois
Default

The area of concern are the door jambs and there is also some on the rear valance under the bumper.
I appreciate your feedback but, isn't acetone a little strong? I am hoping to remove the undercoating and bring back the finish.
Nice looking RS!
Thanks again.
 
  #4  
Old 08-23-2009 | 03:43 PM
GMDCAMARO's Avatar
3rd Gear Member
Joined: Oct 2007
Posts: 1,289
From: Utah
Default

I'm at a body shop where we spray bed-liners. Needless to say, are Spray boy isn't exactly the best.

We've had to wipe over spray off the bed sides multiple times with out any real concerns. Acetone is what we've always used. Be Gentle and use small amounts.

Thats all I have from personal experience.
 
  #5  
Old 08-26-2009 | 06:08 PM
gray80's Avatar
Thread Starter
|
Newbie
Joined: Jul 2009
Posts: 29
From: North Central Illinois
Default

GMD - Thanks for the feedback. I am still a little nervous about Acetone. Since I have run out of ideas, it may be my last resort. When you have used it, does it dull the finish or cut the clear coat?
 
  #6  
Old 09-16-2009 | 10:05 AM
JRs72RS's Avatar
February 2009 ROTM
Joined: Jan 2007
Posts: 411
ROTM Winner's Club
Default

Use a good quality COLD formula oven cleaner. Spray it on, keep checking for the undercoat to loosen and wash off with a pressure washer. As long as you don't leave it on for hours the paint is OK. We have done this on many cars/trucks with great results.
 
  #7  
Old 09-16-2009 | 10:25 AM
GMDCAMARO's Avatar
3rd Gear Member
Joined: Oct 2007
Posts: 1,289
From: Utah
Default

Originally Posted by gray80
GMD - Thanks for the feedback. I am still a little nervous about Acetone. Since I have run out of ideas, it may be my last resort. When you have used it, does it dull the finish or cut the clear coat?
I think It may have dulled a few times, but a quick buff and wax took care of it. I do not know the Condition of your paint though. All undercoating that we've had to remove was on fairly new cars & trucks.
 
  #8  
Old 09-16-2009 | 09:22 PM
gray80's Avatar
Thread Starter
|
Newbie
Joined: Jul 2009
Posts: 29
From: North Central Illinois
Default

I will give that a try. I have been told Acetone works, but I am afraid of the strength of Acetone. That is a beautiful RS! Nice work. Thanks for your reply.
 
  #9  
Old 09-17-2009 | 12:59 AM
GMDCAMARO's Avatar
3rd Gear Member
Joined: Oct 2007
Posts: 1,289
From: Utah
Default

Hey Thanks!

Good Luck!!
 
  #10  
Old 09-17-2009 | 06:34 PM
1969 SS's Avatar
3rd Gear Member
Joined: Apr 2006
Posts: 1,459
From: Massachusetts
Default

I've used gasoline and acetone in the past on different cars I've done

honestly, if acetone ruins the paint, then the paint is on it's way out anyway
 


Quick Reply: Undercoating removal



All times are GMT -5. The time now is 07:12 AM.